Thread Adapters, PP
Product number:
7079502
Manufacturer:
Bürkle GmbH
Packaging information:
Weight:
0.082 kg
Description
For Bürkle pumps and discharge stopcocks.
Properties
| Colour: | Brown/blue |
|---|---|
| Manufacturer Article Number: | 0600-1001 |
| Material: | PP |
| Thread ext.: | S64x5 |
| Thread int.: | DIN71 |
| UNSPSC: | 41121815 |
Skip product gallery
Anti-static set
From
CHF 82.60*
Flow Indicator with paddle wheel, SAN
From
CHF 58.60*
Solvent pump hand operated, for tinplate canisters
From
CHF 795.00*
Hand pumps OTAL®, PP
From
CHF 119.00*
Solvent pump foot operated, with flexible tubing
From
CHF 1,083.00*
Drum pump Pump-it®
From
CHF 202.00*
Barrel pumps, PP, with flexible, PVC dispensing hose and stopcock
From
CHF 231.00*
Drum pump PumpMaster, for acids and chemical liquids
From
CHF 361.00*
Similar products
When dispensing combustible/explosive liquids pump, both dispensing and filling drum involved in the process must be sufficiently earthed, in order to prevent ignition or explosion through electrostatic discharges. Antistatic set, includes three colour-coded connecting cables with clamps, supplied complete in plastic case.
For liquid flows down to 5 ml/sec. Wheel spins freely and speed of rotation is proportional to flow rate. Maximum recommended flow rate up to 95 ml/sec, max 2 bar pressure. Not to be used with corrosive fluids or over +85 °C. Can be used with gases.
For contamination-free removal of organic solvents and flavouring agents. Can be completely closed off with two ball valves so that no dangerous vapours can escape after dispensing. Electrostatic charge can be dissipated through the accessory antistatic set (please order separately).Medium-contacting parts are made of stainless steel (1.4301) and PTFEFor containers up to 60 litresIncl. connector thread for pull-out spouts with Ø 35 mm
Only the tube comes into contact with the liquid when the pumps are used, so that a great deal of liquid can be filled off. The telescopic immersion tube adapts itself to the container height on insertion. This ensures good removal of residual liquid.Good pump capacityFoodsafeDelivery tubes made of PPUniversal bungs made of soft PVC, for container openings of 30 – 70 mmFor weak acids, alkalis and detergents
For filling off high purity liquids such as solvents. Due to the barrel screw joint and the stopcock, the container and the pump can be hermetically sealed. Electrostatic charge can be dissipated through the accessory antistatic set (please order seperately).Medium-contacting parts made of stainless steel (1.4301) and PTFEFor barrels up to 220 litres, immersion tube can be steplessly adjusted to the barrel depthSuitable for steel barrels with R 2'' thread
For rapid and clean emptying from cans, drums and small barrels up to 60 l.Medium-contacting parts made of PP, PE and FKMPrecise dosing, without drippingPump connection suitable for 64 mm dia. (BSI) container threadsStepless length adjustment of immersion tubeThreaded adapters for most commercially-sold containers availableNot suitable for HCl
For decanting acids, caustic solutions and aggressive detergentsExcellent recovery of residual liquid in the barrel provided by base-sitting, non-return valve and steplessly adjustable immersion tubeFor barrels and tanks from 30 to 1000 l
The manual pressure pump is ideally suited for drawing off, decanting and emptying canisters and barrels. The hand pump is used to create excess pressure that forces the liquid out of the container. The stopcock also allows extraction of small quantities of liquid. The PumpMaster container pump is mounted on the container using a flexible stopper with a variable and adjustable diameter. No special thread adapters are required. PumpMaster fits all commercial container openings with a diameter from 46.5 mm to 60 mm. The immersion tube has a length of 95 cm and it can be shortened depending on the size of the container.Green. FKM gasket.Scope of supply: Drum pump, three bungs in different sizes